Kitchen exhaust duct installation, extension and re-routing
The exhaust duct carries smoke, heat and grease from the hood to the outside. It is the longest part of the system and the hardest to change once the ceiling is closed, so the route matters. HoodEx installs kitchen exhaust ducts for new kitchens, extends and re-routes existing ones, and adds access panels so the duct can be cleaned along its whole length.
What's included
- Site visit to trace the route from the hood to the discharge point
- Exhaust duct installed from the hood collar to the exhaust fan
- Duct extensions when the hood or the fan moves
- Re-routing around new walls, beams or other building services
- Access panels added along the run for cleaning and inspection
- Sealed connections to the hood and to the exhaust fan
- Duct insulation against condensation where the duct runs through cooled ceilings
When you need it
- You are fitting out a new kitchen and need the duct planned with the hood and fan
- The hood or the fan is moving, so the duct has to follow
- Your duct has no access panels, so parts of it have never been cleaned
- Grease leaks from joints or drips from the ceiling
- The route is long, with many bends, and the fan struggles
- A cleaning report recommended changes to the duct
How we do it
A good duct route is as short and direct as the building allows, with as few bends as possible. Every bend and every extra length of duct adds resistance the fan has to work against. Horizontal runs should fall back toward the hood, so grease drains to where it can be collected and does not pool in a low point above the ceiling.
A kitchen exhaust duct is a grease duct, not ordinary ventilation ducting. Its joints have to be sealed so grease cannot leak out, and it needs clearance from anything that can burn. NFPA 96 is the standard most kitchens follow for grease duct work. Your landlord, building or local authority may have requirements too, such as where the duct can pass and where it can discharge, so tell us about them at the site visit.
The last section, often called the exhaust fan duct, joins the main run to the fan. It has to match the fan's inlet and be joined so it can be opened when the fan needs cleaning or service.
The duct starts at the hood and ends at the fan, so it is planned with both. See kitchen hood installation and exhaust fan installation. Once the duct is in, it needs regular cleaning: see kitchen duct cleaning.
Having a problem? Smoke, heat, smells, doors that are hard to open or a fan that keeps stopping: see kitchen ventilation problems and solutions.
Duct extension and re-routing
Kitchens change. A new wall goes in, a hood moves to the other side of the room, or a second hood is added for a new cooking line. When that happens, the existing duct can often be extended or re-routed rather than replaced. We look at the condition of the duct you have, and if a section is too damaged or too greasy to keep, we tell you.
Re-routing is also the fix for a duct that was badly planned in the first place: one with long flat runs, sharp bends or a dip where grease collects. A shorter, cleaner route lets the fan move more air with the same effort. For other changes to the system, see kitchen exhaust modification.
Access panels
A duct can only be cleaned where someone can reach it. Access panels are sealed openings in the duct, placed at changes of direction and along long runs, so a cleaning crew can get brushes and scrapers to every section. Some older kitchens have long runs with few or none. Adding them is one of the simplest changes that makes a system safer to run. Our guide to duct access panels explains where they go.
Frequently asked questions
Can you install a duct for a new kitchen hood?
Yes. We plan the duct with the hood and the fan, from the hood collar to the discharge point, and quote after a site visit.
Can you extend our existing exhaust duct?
Usually, yes, if the existing duct is in good condition. We check it at the site visit and tell you if any section should be replaced.
Why does my duct need access panels?
Without them, large parts of the duct cannot be reached for cleaning, and grease builds up there. Panels at bends and along long runs let the whole duct be cleaned.
What is an exhaust fan duct?
It is the section of duct that connects the main exhaust run to the exhaust fan. It has to match the fan's inlet and be easy to open for fan service.
Can the duct pass through other floors or units?
That depends on your building. Many buildings have set routes or shafts for kitchen exhaust. Tell us what your landlord or building management allows and we plan the route around it.
How much does exhaust duct installation cost?
It depends on the length of the run, the number of bends, the access and the building rules, so we quote after a site visit.
More questions? See our full FAQ.
Where we do this
Kitchen exhaust duct installation and re-routing in all seven emirates and Al Ain. Our exhaust duct installation team works in every emirate, with day and night shifts.
Book exhaust duct installation.
Not sure what your system needs? We inspect it first and recommend only what's needed.